When one section of your permanent Christmas lights goes dark, you have to find that failed section first, and you need to find out whether you can replace only that section. Govee Permanent Outdoor Lights Pro is best for homeowners who want to swap a failed section themselves: it allows you to cut out the failed section and replace it with a 16.4ft extension light, as long as the run stays within 200ft. Start with these checks.
Introduction
It’s the night before Thanksgiving, and you switch on the roofline lights. One section over the garage stays dark, or the whole run is out, and the Govee Home App shows it offline.
When this happens, homeowners often fall into three common traps: climbing the ladder when a GFCI (an outlet that cuts power when it detects a ground fault) outlet had just tripped, trying to connect to a 5GHz router, and replacing a whole set when some models let you swap only the failed section.
Here's how to fix permanent Christmas lights: check power and connections from the ground, walk through a step-by-step method to isolate the failed section, explore which lighting systems allow whole-section replacement and how each Govee permanent light handles it, and see when to reach out to official support. If half of a Christmas tree string or seasonal string is dark instead, see how to fix Christmas lights.

Govee Permanent Outdoor Lights Not Turning On? Start With Power
If the whole run stays dark, the problem is usually power or settings, not the lights themselves, so start at the outlet.
- 1. Check the outlet and GFCI: Plug another household appliance or phone charger into the outlet to verify it has power. If the outdoor GFCI outlet is tripped, press the reset button firmly; as UL Standards & Engagement emphasizes, outdoor holiday lights should always be plugged into weatherproof GFCI-protected outlets.
- 2. Check the adapter light: Look at the adapter. When it works normally, you will see a dim green or blue light on its front, near the output end. If the light is off, check the plug at the adapter end first.
- 3. Check the connectors: Unplug the adapter completely to cut power, then make sure the connectors between the adapter, the control box, and each light section are fully seated and tightened.
- 4. Check the segment setting in the app: Open the device page in the Govee Home App, tap settings in the top right, and confirm that the Number of Segments accurately matches the number of sections installed on your roofline.
- 5. Reset the light: Press and hold the control box button for more than 5 seconds to reset the whole set. A plain reset does not require rebinding in the app.
If the whole run is still dark after these checks, move on to the section-by-section check in “How to Find the Dark Section on Permanent Christmas Lights.” If you can see damaged connectors or cable, go to “When to Contact Govee Support.”
Govee Permanent Outdoor Lights Not Connecting to Bluetooth or Wi-Fi
Govee Home App pairs the lights over Bluetooth first, then connects them to your home Wi-Fi, so fix Bluetooth before you troubleshoot Wi-Fi. These steps follow the Govee user manuals for all four models.
If Bluetooth won’t connect:
- 1. Don’t skip the Bluetooth connection steps in the app.
- 2. Keep your phone’s Bluetooth turned on.
- 3. Stay within 1m (3.28ft) of the lights when you pair, with nothing in between.
- 4. Power off the lights and turn off your phone’s Bluetooth. Then turn both back on and try again.
- 5. If it still fails, try another phone. Yours may not be compatible with the app.
If Wi-Fi won’t connect:
- 1. Keep in mind that only 2.4GHz Wi-Fi is supported, not 5GHz. Set the router to 2.4GHz and reconnect.
- 2. Check the Wi-Fi name and password.
- 3. If the lights are too far from the router, move the router closer. You can also test with your phone’s hotspot first to see whether the router is the problem.
- 4. Press and hold the control box for 5 seconds to reset the light. You don’t need to rebind it in the app after the reset.

How to Find the Dark Section on Permanent Christmas Lights
When only part of the run is dark, switch the lights to a solid white or a single color first, so a scene or DIY effect doesn’t look like a failure.
Holiday lights are usually connected in parallel by several groups of series circuits. As the U.S. Department of Energy highlights in its guide on how holiday lights work, when bulbs in a series circuit are loose or faulty, only that specific circuit might not work. However, incandescent bulbs use a shunt, which completes the path, even if the bulb fails. LEDs generally do not use shunts. Permanent lights are also connected section by section, so check the dark section and the connector before it first.
Here is the section-by-section check:
- 1. If some light beads flicker or don’t light, unplug the adapter, wait 5 seconds, and plug it back in. If they are still dark, cut the power and look at the nearest connector before the first dark light. Is it fully seated, wet, or corroded?
- 2. If you cut and spliced the run yourself, check the splice first. A poorly made splice can fail or let water in. Our guide on how to cut and splice permanent lights walks through the steps.
- 3. Remove the last section that still lights up. Then connect each dark section, one at a time, to a section that works. The section that stays dark when connected is the failed one.
- 4. Walk the roofline and look for cable that is pinched, chewed, or crushed by ice. The NFPA advises replacing strings that are worn or have broken cords or loose bulb connections.
Once you find the failed section, whether you can replace just that section depends on the system and the model. The next two sections cover both.
| What you see | Check first | Next step |
| Whole run is dark | Outlet, GFCI, adapter light | Reseat plugs, hold control box 5 seconds |
| App can't connect | Phone Bluetooth, 2.4GHz Wi-Fi | Pair within 3.28ft, then reset the lights |
| Dark from one point on | Connector before the first dark light | Test sections one by one |
| Dark from a splice | Splice connector and seal | Redo the splice per the splice guide |
| Cut or crushed cable | Damaged spot, power off | Stop using it; swap the section or call support |
Steps from Govee user manuals. Unplug the adapter before you touch any connector.
Which Outdoor Christmas Light Systems Let You Swap a Failed Section Quickly
If you want to swap a failed section quickly rather than troubleshoot individual bulbs, choose a system whose manufacturer supports replacing that section for your exact model and sells or supplies the matching part. Here is how the main types compare.
Replaceable-bulb C7/C9 socket strings: Bulbs on the string can be unscrewed and replaced. If there is a single fault, it can be repaired easily. However, they are for seasonal use; you need to put them up and store them every year.
Mini light strings with removable bulbs: Bulbs can be easily changed, but you need to test each bulb one by one. These lights are usually wired in groups in series, so one loose bulb can darken the whole group, as explained earlier. The how to fix Christmas lights guide covers the troubleshooting steps.
Sealed LED strings: Light beads cannot be removed or replaced as the string is sealed. In most cases, the whole string is replaced after failure. Permanent lights are the same: their beads can’t be replaced one at a time like bulbs.
Cuttable permanent roofline lights: With cuttable permanent lights, when the manufacturer supports it, a failed section can be cut out and a new section connected, depending on the model. The Pro and Govee Permanent Outdoor Lights Prism can each have a failed section cut out and replaced with a 16.4ft extension light, with the Prism’s extension light subject to product page availability; Govee Permanent Outdoor Lights 2 Pro can also be cut and spliced, but if it fails, contact Govee support to have a replacement string sent.
Before you buy, ask yourself three questions:
- Can I replace a failed section myself, or does it go back to the manufacturer?
- Is the matching section sold or supplied for my exact model?
- Is there a total-length limit after I add the new section?
Here is how each Govee permanent light handles a failed section.
How to Replace a Failed Section on Govee Permanent Outdoor Lights
All four work with Matter, Alexa, and Google Assistant, and each product page lists a 3-Year Warranty.
| Option | Fix for a failed section | Weather rating | Best for | Price by length |
| Govee Permanent Outdoor Lights Pro | Cut it out, add a 16.4ft extension light (not the black 200ft kit) | IP67 lights, indoor adapter | Homeowners who want to swap a failed section themselves |
100ft $439.99 150ft $599.99 200ft $759.99 |
| Govee Permanent Outdoor Lights Prism | Same fix; check extension light availability | IP68 lights, outdoor adapter | A custom roofline in harsh weather |
150ft $699.99 200ft $859.99 |
| Govee Permanent Outdoor Lights 2 Pro | Replacement string from Govee support | IP68 lights, IP67 adapter | A complex roofline with split runs |
100ft $499.99 200ft $799.99 |
| Govee Permanent Outdoor Lights 2 | Can't swap one section; not cuttable | IP67 lights | A simple roofline you don't want to cut |
50ft $179.99 100ft $279.99 150ft $419.99 |
Note: IP67 = dust-tight, survives brief immersion; IP68 = dust-tight, survives longer immersion.
Prices and specs from Govee product pages. Matter is a trademark of the Connectivity Standards Alliance.
If you want to swap a failed section yourself, choose the Pro. You can buy the 16.4ft extension light directly on the product page. It has a 200ft maximum length, but going above 150ft requires a driver module (a Govee add-on needed to run the lights past 150ft), which is included with the 200ft package).
If your roofline faces hard winters or strong sun and needs a custom length, choose the Prism. It can be cut, spliced, and extended with professional guidance, and it can work outdoors and operate from -22°F to 140°F. A failed section can also be replaced with a 16.4ft extension light, subject to product page availability.
If your roofline has corners or branches you want to light separately, choose the 2 Pro. The Y connector enables independently controlled split runs. If a string fails, contact Govee support to have a replacement string sent.
If you have a simple roofline and don’t want to cut anything, choose Permanent Outdoor Lights 2. It links up to 9 light segments and 4 extension cables and spans up to 150ft total. It cannot be cut or trimmed; the 150ft kit does not support additional light extensions, and it cannot be mixed with the first-generation Permanent Outdoor Lights. A single section can’t be swapped out, so contact Govee support if part of it fails.
To see all Govee permanent lights and lengths, browse permanent outdoor lights.
How to Swap a Failed Section on Govee Permanent Outdoor Lights Pro
Govee Permanent Outdoor Lights Pro is best for homeowners who want to swap a failed section themselves, because a dark section can be cut out and replaced with a 16.4ft extension light.
- 1. Find the failed section with the section-by-section check, and cut the power first.
- 2. Following the Govee cut-and-splice guide, cut at both ends of the failed section, each time between two light beads.
- 3. Connect the 16.4ft extension light and fit the waterproof connectors as shown in the guide.
- 4. Turn the power back on, check the whole run in white, and then check the number of segments in the app.
Keep these limits in mind:
- Cost: the 16.4ft extension light is bought separately.
- Restrictions: the total length can’t go over 200ft, and a driver module is needed beyond 150ft (the 200ft kit includes one). The adapter is for indoor use only. The black 200ft kit (H706C) uses a new chip and shares only the adapter with other Pro kits, so it can’t take an extension light, driver module, or control box; if a section fails, contact Govee support. Check the model before ordering. If you have the white 200ft kit, trim the extension light so the finished run stays at 200ft or less; a shorter run is fine.
- Extra steps: you must do the cutting and splicing yourself, with a professional wire stripper and one waterproof connector at each end. A poor splice can fail or let water in.
Govee Permanent Outdoor Lights Pro costs $439.99 for 100ft, $599.99 for 150ft, and $759.99 for 200ft. The 16.4ft extension light costs $69.99.

When to Contact Govee Support
Contact Govee support if a cable is damaged, a section stays dark after you reseat the connectors and reset the light, or you own a Prism, 2 Pro, or Permanent Outdoor Lights 2 with a failed section. All four product pages show a 3-Year Warranty, and the warranty starts on the date of delivery. Quality problems within 3 years can be returned or exchanged; check details in the Govee warranty policy. Before you climb the ladder, cut the power and have someone hold the ladder.
Always follow the product manual and local electrical codes. For hardwired installations, hire a licensed electrician.
Conclusion
If your permanent lights don’t turn on, check the power, the adapter light, and the app settings from the ground, then hold the control box for 5 seconds to reset. If only one section is dark, check section by section until you find the failed one. To replace a failed section yourself, choose Govee Permanent Outdoor Lights Pro, and for other situations, go back to the comparison table. Find the failed section, check what your model supports, and keep a 16.4ft extension light on hand if you own the Pro.
FAQs About Fixing Permanent Christmas Lights
Which outdoor Christmas light systems let me swap a failed section quickly instead of troubleshooting my bulbs?
Choose a system whose maker supports whole-section swaps and sells or supplies the matching section. Then add as long as the run stays within 200ft after 16.4ft extension light. Govee Permanent Outdoor Lights Pro suits homeowners who want to swap a failed section themselves, and the Prism suits a custom roofline in harsh weather; both let you cut the section out and splice in a 16.4ft extension light, the Prism’s subject to product page availability. Replaceable-bulb C7/C9 strings swap single bulbs but come down yearly.
How do I reset my Govee permanent outdoor lights?
Press and hold the control box button for more than 5 seconds, which resets the whole light. All four models reset the same way, and a plain reset doesn’t require rebinding in the Govee Home App.
Do my Govee permanent outdoor lights work with 5GHz Wi-Fi?
No, all four of these permanent light models support 2.4GHz Wi-Fi only, not 5GHz. If your router broadcasts 5GHz, set it to 2.4GHz and reconnect the lights. Keep your phone’s Bluetooth on while you pair, and stay within 1m (3.28ft) of the lights with nothing in between.
Can I replace just one section of my Govee permanent outdoor lights?
It depends on the model. Pro and Prism owners can cut out the failed section and add a 16.4ft extension light, keeping the finished run at 200ft or less (the Prism’s extension light is subject to product page availability). The Pro’s black 200ft kit is the exception: it can’t take an extension light, so contact Govee support. For the 2 Pro, contact Govee support for a replacement string; Permanent Outdoor Lights 2 can’t have just one section replaced.
How long is the warranty on my Govee permanent outdoor lights?
The product pages for Govee Permanent Outdoor Lights Pro, Prism, 2 Pro, and Permanent Outdoor Lights 2 all show a 3-Year Warranty, and the warranty starts on the date of delivery. If a quality problem shows up within those 3 years, the lights can be returned or exchanged, so contact Govee support.
Which outdoor Christmas lights are easiest for me to repair when one section fails?
It depends on what you want to replace. Replaceable-bulb C7/C9 strings let you swap a single bulb, while sealed LED strings are usually replaced whole. For permanent lights, choose a model that supports replacing a whole section, such as Govee Permanent Outdoor Lights Pro, where you cut out the failed section and add a 16.4ft extension light you can buy on the product page.
Can I buy replacement parts for my Govee permanent outdoor lights?
It depends on the model. The Pro’s product page lists the 16.4ft extension light, driver module, adapter, and control box separately, and Permanent Outdoor Lights 2 lists an extension light too. The Prism’s extension light is subject to product page availability, and the 2 Pro has no parts sold separately, so contact Govee support to have a replacement string sent if it fails.



































